10 IM Tibia Nailing Assembly Instructions
& Part Reference Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Advance Control Base Preparation and Installation Prior to procedure set up, refer to the Advance Control Base Preparation and Installation section and complete the required steps. Refer to the Owners Manual section 4 for additional base installation instructions. VIEW NOW CONTINUE WITH SETUP Accessory Clamp Attach (2) AA to the frame near the foot end with receiver on the operative side of the table. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP AA Tibia Traction Upright Insert Y into AA from the bottom with receiver facing operative side of table. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP V,W Traction Unit Install P-1 into each X-1. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP P-1 Foot Plate Attach P-2 to P-1. The Traction Boot may not be used if an interlocking nail is to be inserted. Apply Safety Strap (FF) to table. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP P-2/FF Center Support Board Install F and secure with locking knob and Center Support Plug. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP F Well Leg Support Swing Arm Install BB-3 (part is not visible) to the non-operative side of the table and lock. Ensure the T-handle on BB-3 is facing down. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP BB-3 Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Patient Instructions Transfer the patient in supine position and secure with patient safety straps (FF). Tibia Support Upright & Tibia Counter - Traction Post Insert L into middle of F. Attach M to L and reposition patient on the table. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP L/M Well Leg Support Install BB-1 onto BB-3. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP BB-1 Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Patient Instructions Place patient’s non-operative leg onto BB-1, pad, and secure. Place the patient’s operative foot on the Traction Foot Plate
(P-2), pad, and secure. Universal Side Rail Adaptor (XX) and Clark Socket (YY) Mount XX on the non-operative side of the table (two locations). Mount YY to proximal XX (part not visible). Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP XX/YY Pivoting Arm Board Install RR onto distal XX (part not visible) on the non-operative side of the table. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP RR Cross Arm Support Install SS onto YY on the non-operative side of the table. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP SS Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Patient Instructions Secure patient’s arm onto RR and SS. The IM Tibia Nailing setup is now complete. For more information or questions about this setup or any setup, please refer to the Owner's Manual or contact Mizuho OSI for additional support. Setup Complete