9 IM Femoral Nailing: Lateral Decubitus Position
Unilateral Skin Traction Base Preparation and
Orthopedic Top Installation Trios Table Base Preparation and Installation Prior to procedure setup, refer to the Trios Table Base Preparation and Installation section and complete the required steps. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP View Orthopedic Top Installation Orthopedic Traction Arc Installation Installation of Trios Traction Arc Following Step 1, view the installation of Trios Traction Arc section and complete the required steps. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP View Traction Arc Installation Orthopedic Traction Arc Positioning Position the Trios Traction Arc Slide the Trios Traction Arc and the Anatomical Adjustment Roller to the non-operative side of the table and lock. With the Trios Traction Arc extended to its full length on the non-operative side of the table, slide one Tractor to each end of the Trios Traction Arc and lock with the Tractor Lock. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Traction Unit Upright Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 1 Install into the tractor on the non-operative side of the table. Traction Extension Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 2 Install into the Traction Unit Upright receiver facing up. Traction Unit Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 3 Install Traction Unit into Traction Extension. Traction Boot or Foot Plate with Soft Boot Attach Traction Boots or Soft Boots with foot plates to both Traction units. Rotate both 90º towards operative side of the table by releasing the gold lock handle. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 4 Center Support Board Install the Center Support and secure with locking knob and Center Support Plug. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 5 Accessory Clamp Attach two Accessory Clamps to the frame near the foot-end with receiver on the non-operative side of the table. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 6 Leg Support Insert the Leg Support into the Accessory Clamp. Position at table top height. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 7 Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Patient Instructions Transfer the patient to the table in the supine position. With surgical team supporting, position the patient with the non-operative thigh on the Center Support Board. Roll patient into the lateral position; operative leg up. Secure with patient safety strap. Ilium Post and Lateral Perineal Post Insert Ilium Post and Lateral Perineal Post to the non-operative side of the Center Support Board. Rotate the Ilium Post to adjust the Lateral Perineal Post approx. 30º with the elbow toward the foot-end of the table and lock. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 8 Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Patient Instructions Place lower (non-operative) leg on Leg Support and adjust the board position as required, pad and secure. Position patient’s foot on the operative leg into the Traction or Soft Boot, pad and secure. Universal Side Rail Adaptor and Clark Socket Mount the Universal Side Rail Adaptor on the non-operative side of the table (two locations). Mount the Clark Socket to the proximal Universal Side Rail Adaptor. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 9 Pivoting Arm Board Install the Pivoting Arm Board onto distal Universal Side Rail Adaptor on the non-operative side of the table. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 10 Cross Arm Support Install the Cross Arm Support into the Clark Socket on the non-operative side of the table. Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP 11 Standard Component Installation and Adjustment Prior to procedure set up, refer to the Standard Component Installation and Adjustment section and complete the required steps. VIEW NOW CONTINUE WITH SETUP Patient Instructions Pad and secure patient’s arms onto the Pivoting Arm Board and Cross Arm Support. The IM Femur Nailing: Lateral Decubitus Position Unilateral Skin Traction setup is now complete. For more information or questions about this setup or any setup, please refer to the Owner's Manual or contact Mizuho OSI for additional support. Setup Complete